Does triplet SF need a surfactant?

Answer: Triplet SF Selective Herbicide does not require the use of a surfactant.

What weeds does triplet SF kill?

Triplet SF is an effective liquid post-emergent broadleaf herbicide formulation of two phenoxy herbicides and dicamba that selectively controls broadleaf weeds in turfgrass. Triplet SF is perfect for control of hard-to-kill broadleaf weeds, such as dandelion, clover, henbit, and plantains in turfgrasses.

Is triplet SF pet safe?

For turf use, do not allow people (other than applicator) or pets on treatment area during application. Do not enter treatment areas until spray has dried. Use this product only in accordance with its labeling and with the Worker Protection Standard, 40 CFR Part 170.

Does triplet kill grass?

It contains a combination of three powerful active ingredients that offer effective control of hard-to-kill weeds like ground ivy, clover, dandelion, henbit, plantains, pigweed, poison ivy, ragweed, and more on both cool and warm season grass.

How long does it take triplet to work?

3-D Herbicide Triplet Alternative will last 3 to 5 years if kept out of extreme temperatures (above 90 and below freezing) and direct sunlight. Each 2.5 gallon jug of 3-D will treat up to 7 acres of turf grasses for broadleaf weeds. 3-D takes approximately 2 weeks to kill weeds.

How long does triplet need to be on before rain?

For optimum results: (1) turf should not be mowed for 1 to 2 days before and after application; (2) do not apply if rain is expected within 4 hours after the application, delay irrigation cycle for 24 hours. Reseed no sooner than three to four weeks after application of this product.

How many gallons of water are in a triplet SF?

According to the Triplet SF Selective Herbicide product label, the rate of this product is based on the grass type. For use on Bahiagrass, Bluegrass (Common), Bermudagrass, Fescue, Ryegrass or Zoysiagrass you would use 1.1-1.5 fl oz per 1,000 sq ft. in 0.5-5 gallons of water.

How do you get rid of crabgrass permanently?

The best weapon in your quest to kill crabgrass is pre-emergence herbicide (also called crabgrass preventer). Apply it in the spring before the crabgrass seeds sprout. The granular herbicide works by creating a chemical barrier at the surface of the soil. As the seeds germinate, they take in the herbicide and die.

How long should I wait to water after spraying for weeds?

Do not water right after applying a weed killer. Wait a minimum of two days before watering.

What is Nufarm triplet SF selective herbicide?

Leave Us a Message Nufarm Triplet SF Selective Herbicide is a specially formulated liquid herbicide that provides efficient post-emergent control of broadleaf weeds in turfgrasses.

What is triplet herbicide used for?

Triplet SF is an effective liquid post-emergent broadleaf herbicide formulation of two phenoxy herbicides and dicamba that selectively controls broadleaf weeds in turfgrass. Triplet SF is perfect for control of hard-to-kill broadleaf weeds, such as dandelion, clover, henbit, and plantains in turfgrasses.

What is triplet SF used for?

PPE Fact Sheet Triplet SF is an effective liquid post-emergent broadleaf herbicide formulation of two phenoxy herbicides and dicamba that selectively controls broadleaf weeds in turfgrass. Triplet SF is perfect for control of hard-to-kill broadleaf weeds, such as dandelion, clover, henbit, and plantains in turfgrasses.

How long does it take for triplet SF selective herbicide to work?

It can take up to two weeks to start to see results after application of Triplet SF Selective Herbicide . Was this answer helpful to you? Yes No Is it recommended to apply Triplet SF with a surfactant or methylated seed oil?